0123456789ABCDEFLL
module: 
 procedure: 
 called from 
module:  0
(Out of stack space or no modules loaded.
(Attempting to call uninitialized module.
'Invalid pointer or corrupt module code.
Program error - code 
 in FarOutgoing.
Error while calling module: 
, procedure: 
 from module 
TIRONE AND QUADRANT
4The Tirone Level and Quadrant Lines commands are not
+available in the demo version of Metastock-
Professional.
4These studies draw a series of horizotal lines which
6divide prices into equal segments based on their high/
:low range. They are helpful in locating support/resistance
levels.
POINTER MODE ON
4The Pointer is now turned ON (it is displayed in the
&upper right-hand corner of the chart).
7Pressing the [/] key will display the Pointer Selection
0Menu.  Pressing [ESC] will turn the pointer OFF.
POINTER MODE OFF
The Pointer is now turned OFF
4Pressing the [/] key will display the Main Selection
Menu.
Angle of Trendline
Data Window
Percent Retracement
Moving Average Window
Y-Axis Window
Intersect Lines On/Off
Find a Date
Flip Pointer
Leave Arrow
Pointer Mode Off
Write Text
Andrews' Pitchfork
Cycle Lines
Fibonacci, Arcs
Fibonacci, Fan Lines
Fibonacci, Time Zones
Gann Angle/Grid
Linear Bands
Quadrant Lines
Speed Resistance Lines
Tirone Levels
End Trendline
Extend Trendline
Horizontal Line
Linear Regression
Parallel Line
Remove/Restore
Start Trendline
Trendline by Angle
Vertical Line
POINTER SELECTION MENU
.   Data      Pointer     Studies    Trendlines
01/01/80
	         
P&F DATA WINDOW
Pointer at column #
DATA WINDOW
	Date  -> 
	Indcr -> 
	High  -> 
	Close -> 
	Low   -> 
	Volume-> 
POINTER VALUE
	Date  -> 
	Pointr-> 
MOVING AVERAGE
	Date  -> 
	Indcr -> 
	Close -> 
	Averge-> 
NOT AVAILABLE 
"That command is not available when
$a Point & Figure chart is displayed.
To display a BAR chart:
' 1) Press any key (remove this window).
# 2) Press [ESC] (turn pointer off).
% 3) Press [Z]oom (display bar chart).
NOT AVAILABLE 
%That command is not available when a 
$"rubberband" trendline is displayed.
%You should first use the [R]emove or 
%[E]nd command to complete the current
"rubberband" trendline.
NOT AVAILABLE 
%That command is ONLY available when a
$"rubberband" trendline is displayed.
%Use the [S]tart command to display a 
"rubberband" trendline.
TEXT MODE STATUS
TEXT MODE ON
	FIND DATE
$Enter the date to find (mm/dd/yy) ->
ANGLE OF TRENDLINE
Angle : 
Slope : 
Last trendline  
not available.
Press any key...
Move pointer to 
 point and press [ENTER]. 
FIRST
SECOND
THIRD
TRENDLINE BY ANGLE
Enter angle of the   
trendline (1-179) ->
ANDREWS' PITCHFORK
PERCENT RETRACEMENT
PERCENT RETRACEMENT
Price #1 : 
Price #2 : 
Price #3 : 
           ----------
% Retrace  
33 1/3%  = 
40    %  = 
50    %  = 
60    %  = 
66 2/3%  = 
WAS  : DAY=
 VALUE=
 RISE=
 RUN=
 STEP=
START: DAY=
 VALUE=
END  : DAY=
 VALUE=
WORLD IS =
 WINDOW IS =
GANN ANGLE LINES
[L]ine or [G]rid? G
Enter ratio below:   
_______  x  ________
 (days)     (points)
CYCLE LINES
Initial cycle line
spacing -->
Date: 
 Spacing: 
pO	 x * AF =
 SQR=
 SQR=
SQRT=
SETUPJUMPTABLE FOLLOWS
FARCALLHANDLER FOLLOWS